Weslo compact XL Manual do Utilizador

USER'S MANUALSerialNumberDecalModel No. WETL40708.0Serial No.CAUTIONRead all precautions and instruc-tions in this manual before usingthis equipm

107. Identify the Right Handrail Cover (95) and theLeft Handrail Cover (93). Slide the end of theRight Handrail (94) through the hole in the RightHand

119. Attach the Right Handrail (94) to the Console(109) with an M5 x 16mm Screw (13), an M5Star Washer (12), and two M4.2 x 19mmScrews (10). Make sure

1211. Attach the Console (109) to the Uprights (96,98) with six M8 x 16mm Bolts (17) and six 5/16"Star Washers (2). Start all six Bolts beforetig

1314. With the help of a second person, raise theRight Upright (98) and the Left Upright (notshown). Then, raise the Frame (67) to the posi-tion shown

1415. Attach the Rear Feet (70, 71) to the Frame (67)with four #8 x 1" Screws (7).Lower the Frame (67) (see HOW TO LOWERTHE TREADMILL FOR USE on

15THE PRE-LUBRICATED WALKING BELTYour treadmill features a walking belt coated with high-performance lubricant. IMPORTANT: Never apply sili-cone spray

16FEATURES OF THE CONSOLEThe treadmill console offers a selection of featuresdesigned to make your workouts more effective. Whenyou select the manual

17HOW TO TURN ON THE POWERIMPORTANT: If the treadmill has been exposed tocold temperatures, allow it to warm to room tem-perature before turning on th

18• Incline—This mode displays the incline of thetreadmill whenever the incline changes.•Pulse—This mode displays your heart rate when-ever you use th

19HOW TO USE A PRESET WORKOUT1. Insert the key into the console.See HOW TO TURN ON THE POWER on page 17.2. Select a preset workout.To select one of th

2WESLO is a registered trademark of ICON IP, Inc.WARNING DECAL PLACEMENTThis drawing shows the locations of the warningdecals. If a decal is missing o

20HOW TO FOLD AND MOVE THE TREADMILLHOW TO FOLD THE TREADMILL FOR STORAGEBefore folding the treadmill, adjust the incline to thelowest position. If yo

21HOW TO LOWER THE TREADMILL FOR USE1. Hold the upper end of the treadmill with your right hand.Pull the latch knob to the left and hold it. It may be

22TROUBLESHOOTINGMost treadmill problems can be solved by following the steps below. Find the symptom that applies, andfollow the steps listed. If fur

23Locate the Reed Switch (55) and the Magnet (49)on the left side of the Pulley (58). Turn the Pulleyuntil the Magnet is aligned with the Reed Switch.

24PROBLEM: The walking belt is off-center or slips when walked onSOLUTION: a. If the walking belt is off-center, first remove the keyand UNPLUG THE PO

25These guidelines will help you to plan your exerciseprogram. For detailed exercise information, obtain areputable book or consult your physician. Re

26PART LIST—Model No. WETL40708.0 R0808AKey No. Qty. Description Key No. Qty. Description123/8" x 2" Bolt265/16" Star Washer33 3/8"

27Key No. Qty. Description Key No. Qty. Description101 1 Base102 4 Wheel Spacer103 2 Wheel104 1 Latch Cap105 16 8" Wire Tie106 1 Latch Warning De

283030145542425029515221325453193857565931386057586514545332194242632147512966676462333638397197170719364468693938316133194023233330303030303030313128

724343434325732024263248485813434352283803522278246387738767946878889149086141414397574786113EXPLODED DRAWING B—Model No. WETL40708.0 R0808A29

1. Before beginning this or any exercise pro-gram, consult your physician. This is espe-cially important for persons over age 35 orpersons with pre-ex

17101013414121710959492109341139110101721721791297989615991589910016181001810014101119791021031059055448121214141416100102102102103910710788EXPLODED D

31110111110101045109EXPLODED DRAWING D—Model No. WETL40708.0 R0808A

Part No. 265906 R0808A Printed in China © 2008 ICON IP, Inc.ORDERING REPLACEMENT PARTSTo order replacement parts, see the front cover of this manual.

420. Do not attempt to raise, lower, or move thetreadmill until it is properly assembled. (SeeASSEMBLY on page 6, and HOW TO FOLDAND MOVE THE TREADMIL

5Thank you for selecting the new WESLO®COMPACTXL treadmill. The COMPACT XL treadmill offers a selec-tion of features designed to make your workouts at

ASSEMBLYAssembly requires two persons. Set the treadmill in a cleared area and remove all packing materials; do notdispose of the packing materials un

71. Make sure that the power cord is unplugged.Orient the Base (101) as shown.Attach four Base Feet (100) to the Base (101) inthe locations shown with

84. To protect the floor or carpet from damage,place a piece of cardboard underneath bothends of the Frame (67).With the help of a second person, rais

96. Hold the remaining Upright Spacer (99) betweenthe Left Upright (96) and the Lift Frame (75),with the outer side of the Upright Spacer fac-ing the