Model No. WLTL39806.0Serial No. CAUTIONRead all precautions and instruc-tions in this manual before usingthis equipment. Save this manualfor future re
14.Make sure that all parts are properly tightened before you use the treadmill. Note: Extra hardware maybe included. Keep the included allen wrenches
11OPERATION AND ADJUSTMENTTHE PRE-LUBRICATED WALKING BELTYour treadmill features a walking belt coated with high-performance lubricant. IMPORTANT: Nev
12FEATURES OF THE CONSOLE The treadmill console offers several features designedto make each workout more effective and enjoyable.When the manual mode
HOW TO TURN ON THE POWERPlug in the power cord(see page 11). Next, lo-cate the reset/off circuitbreaker on the treadmillframe near the powercord. Make
14The lower left cornerof the display willshow the elapsed timeand the distance thatyou have walked orrun during your work-out. The lower left corner
15HOW TO USE A PRESET PROGRAMInsert the key into the console.See HOW TO TURN ON THE POWER on page13. Select a preset program.To select a preset pro-gr
16THE INFORMATION MODEThe console features an information mode that keepstrack of treadmill usage information and allows you toselect a system of meas
17HOW TO FOLD AND MOVE THE TREADMILLHOW TO FOLD THE TREADMILL FOR STORAGEBefore folding the treadmill, adjust the incline to the lowest position. If t
18HOW TO LOWER THE TREADMILL FOR USE1. Hold the treadmill with your right hand as shown. Pull thelatch knob to the left and hold it. Pivot the frame d
19TROUBLESHOOTINGMost treadmill problems can be solved by following the steps below. Find the symptom that applies, andfollow the steps listed. If fur
TABLE OF CONTENTSIMPORTANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
20PROBLEM: The walking belt slows when walked onSOLUTION: a. Use only a single-outlet surge suppressor that meets all of the specifications described
21CONDITIONING GUIDELINESThe following guidelines will help you to plan your ex-ercise program. For more detailed exercise informa-tion, obtain a repu
22SUGGESTED STRETCHESThe correct form for several basic stretches is shown at the right. Move slowly as you stretch—never bounce.1. Toe Touch StretchS
23PART LIST—Model No. WLTL39806.0 R1206AKey No. Qty. DescriptionKey No. Qty. DescriptionKey No. Qty. Description1 1 Hood2 21 3/4" Screw3 1 Motor
80514981817141582839732968632735273838292409289876810015943311858484583031256767492525252525252525259944744484854141528022232367673324EXPLODED DRAWING
551222222368103202828205681585879927726595858777726777710581219131360731312914414625EXPLODED DRAWING B—Model No. WLTL39806.0 R1206A
724270622297123795396939135357393957511081362636413666539613961579913541354934665936346104646613421011062410210578237951616579521992195999976767901071
2224848222272275363488504743384511011110927EXPLODED DRAWING D—Model No. WLTL39806.0 R1206A
LIMITED WARRANTYICON Health & Fitness, Inc. (ICON) warrants this product to be free from defects in workmanship andmaterial, under normal use and
31. It is the responsibility of the owner to ensurethat all users of this treadmill are adequatelyinformed of all warnings and precautions.2. Use the
421. When folding or moving the treadmill, makesure that the storage latch is fully closed.22. Inspect and properly tighten all parts of thetreadmill
5Thank you for selecting the new WESLO®Cadence 50SE treadmill. The Cadence 50 SE treadmill combinesadvanced technology with innovative design to help
ASSEMBLYTo hire an authorized service technician to assemble the treadmill, call toll-free 1-800-445-2480.Assembly requires two persons.Set the treadm
72. Attach two Round Base Pads (57) and an Extension LegPad (61) to the Upright Base (69) and Extension Leg(63) with four 1" Tek Screws (39) as s
87. Identify the Right Handrail (72), which has a large hole inthe left side. Feed the Upright Wire (42) into the hole inthe bottom of the Right Hand
9429. Touch the Right Handrail (72) to discharge any static.Slide the sleeve off the connector on the Upright Wire(42) as shown in the inset drawing.
Comentários a estes Manuais